T-Drill plans an IPO

A new company is planning an IPO!

T-Drill Oyj (“T-DRILL” or the “Company”) is an international technology company that develops equipment and methods for the fabrication of industrial metal pipes.

T-DRILL is planning an initial public offering consisting of a share sale and a share issue (the “Offering”) and to apply for the listing of its shares on the Nasdaq First North Growth Market Finland marketplace (“First North”) operated by Nasdaq Helsinki Ltd (the “Listing”) during the fourth quarter of 2026.

Information on the planned Offering

The planned Offering is expected to consist of an offering of new shares in the Company for subscription via a share issue, and in addition, certain existing shareholders of the Company are expected to offer existing shares in the Company for purchase. The planned Offering is expected to consist of a public offering, an institutional offering, and a personnel offering.

The aim of the planned Offering is to increase T-DRILL’s general brand awareness among customers, partners, potential employees, and investors, to raise capital to enable the execution of its international growth strategy, to broaden the Company’s shareholder base, to generate liquidity for the share, and to enable more efficient use of the shares in employee retention and incentive programs as well as in potential acquisitions.

T-DRILL aims to raise gross proceeds of approximately EUR 10.0 million from the share issue by offering new shares for subscription. The proceeds from the share issue are intended to be used, in accordance with the Company’s strategic objectives, to develop production capacity and automation, expand commercial presence, develop the technology and solution portfolio, expand into new customer segments, broaden the offering toward customer-specific solutions, and expand lifecycle services and the service network. Any funds remaining after financing these initiatives may also be used in part for acquisitions.

Ahlström Invest B.V., Danske Invest Rahastoyhtiö Oy, Ilmarinen Mutual Pension Insurance Company, LähiTapiola Kasvusijoitus Ky, the OP-Suomi Pienyhtiöt investment fund managed by OP-Rahastoyhtiö Oy, certain funds managed by Sp-Rahastoyhtiö Oy, and UB Omaisuudenhoito Oy on behalf of and for the account of its investment clients (together, the “Cornerstone Investors”) have each separately, through commitments given on November 13, 2026, and November 16, 2026, committed to purchase or subscribe for offered shares for a total of approximately EUR 40 million in the Offering, assuming that the valuation of the Company’s entire share capital prior to the funds raised in the share issue is at most EUR 175 million.

T-DRILL in brief

T-DRILL is an international technology company that develops equipment and methods for industrial metal pipe processing and provides related lifecycle services. In its own view, T-DRILL is a pioneer in pipe fabrication solutions that generate a sustainable competitive advantage for customers. The solutions offered by the Company improve pipe processing efficiency by reducing work stages, material consumption, and the need for welding, as well as enhancing process quality. According to the Company’s own studies and evaluations received from customers, the Company’s technologies enable savings of up to 80 percent in materials, working hours, and costs compared to traditional methods.

T-DRILL’s business is built on four core technologies: collaring, flanging, chipless cutting, and tube end forming. The Company’s solutions are based on proprietary technology developed over decades, specialized expertise in pipe fabrication, and an extensive patent portfolio. The Company’s products serve a broad customer base across multiple industrial sectors, key among which are currently HVAC, data centers, shipbuilding, the automotive industry, process piping, construction, and water systems. The Company’s customers operate in various industrial and infrastructure sectors worldwide.

In addition to its four existing core technologies, the Company has four new technologies under development: internal pipe welding (T-InWeld), internal pipe collaring (T-InForm), pipe punching, and orbital pipe cutting and beveling. The technologies under development will enable expansion into new pipe processing customer segments where pipeline components face special requirements. These sectors include the oil and gas industry and the energy industry within the process industry segment, as well as the high-purity and high-quality requirement segments formed by the chemical and pharmaceutical, semiconductor, and food and beverage industries.

The equipment manufactured by T-DRILL is durable and long-lasting. The extensive installed base accumulated over decades forms the foundation of the Company’s lifecycle services business worldwide. As part of equipment sales, the Company provides customers with equipment installation, training, and commissioning. In addition, the Company offers services throughout the entire lifecycle of the equipment, covering technical support, maintenance services, tooling and spare parts, modernizations, and TD-Care service agreements. Lifecycle services accounted for approximately 30 percent of the Company’s revenue in 2025. The significant share of services supports business profitability, continuity, and predictability, as well as the building and expansion of long-term customer relationships.

T-DRILL operates across seven locations: two sites in Laihia, as well as sites in Isokyrö and Kurikka, Finland; a US location in Atlanta; a South Korean location in Seoul; and a German location in Düsseldorf.

The Company’s revenue for the financial year ended December 31, 2025, was EUR 29.2 million, EBITDA was EUR 5.0 million, and operating profit was EUR 4.6 million. For the nine-month period ended September 30, 2026, the Company’s revenue was EUR 43.6 million, EBITDA was EUR 13.6 million, and operating profit was EUR 13.2 million.

CEO Jouni Matikainen:

“Over its roughly fifty-year history, T-DRILL has built a strong position as an international pioneer in pipe fabrication solutions. In recent years, we have grown strongly and profitably, but we still see significant opportunities to strengthen our position globally. Our goal is to grow in existing and new markets, expand our technology and solution portfolio, and serve our customers even more comprehensively throughout the equipment lifecycle. The planned listing would be a natural next step for us, supporting the execution of T-DRILL’s growth strategy and long-term development as an international technology company.”

Key strengths

The Company’s management believes that the following factors are key strengths of T-DRILL in particular:

  • A strong position in a growing global market, supported by industry’s increasing demands for productivity and resource efficiency
  • A pioneer in pipe fabrication solutions that enhance customer competitiveness
  • A significant share of lifecycle services provides continuity and predictability
  • An efficient business model and strong financial track record
  • Excellent prerequisites to continue profitable growth

T-DRILL’s growth strategy

According to the Company’s strategy, its objective is significant profitable revenue growth by expanding the product portfolio into new customer segments, strengthening geographical presence, and scaling lifecycle services. At the core of the strategy is the competitive advantage based on the Company’s core technologies, which the Company aims to leverage in both existing and new markets and industries.

T-DRILL has identified several growth opportunities in both existing and new markets to achieve its targets. The Company’s strategy is based on six mutually reinforcing growth drivers:

  1. Expanding production capacity and investing in machinery and production automation
  2. Strengthening commercial presence and establishing new subsidiaries in existing and new geographic markets
  3. Developing the technology and solution portfolio
  4. Expanding into new, especially technically more demanding customer segments
  5. Broadening the offering toward customer-specific applications and broader integrated solutions
  6. Growing lifecycle services and the local service network globally

The Company is also evaluating acquisition opportunities as part of its growth strategy. The Company’s objective is to identify targets that support its position in pipe fabrication solutions and adjacent areas, complement the product and technology offering—for example, in terms of automation—and expand the service business and the utilization of the installed equipment base. In addition, the Company may consider acquisitions that support its geographic expansion in growth markets or enable access to new customer segments.

Financial targets and dividend policy

The Company aims to grow its revenue to approximately EUR 100 million by the end of 2027. The Company’s revenue was EUR 23.0 million in 2024 and EUR 29.2 million in 2025. The share of lifecycle services in revenue was approximately EUR 6.5 million in 2024 (28.2 percent of revenue) and approximately EUR 8.6 million in 2025 (29.4 percent of revenue). In 2026, strong revenue growth is weighted especially toward industrial machine sales. Revenue from lifecycle services is estimated to continue growing, but more moderately than machine sales, causing its relative share of revenue to decrease. At the same time, the growing base of delivered equipment creates the foundation for future growth in lifecycle services. The Company’s 2027 revenue target is based on the execution of its growth strategy, an estimated 15–20 percent share of revenue from lifecycle services, and leveraging the order backlog of approximately EUR 55 million allocated for 2027 (as of September 30, 2026). The operating margin (EBIT margin) was 16.6 percent in 2024 and 15.6 percent in 2025. The Company targets an operating profit margin of 23–27 percent in 2027.

T-DRILL’s medium-term target is to grow its revenue to EUR 130 million by the end of 2030. Approximately EUR 110 million of the revenue target is intended to be achieved through organic growth. The target is for equipment sales to account organically for approximately EUR 80 million of revenue by the end of 2030, and lifecycle services for approximately EUR 30 million. In addition, the Company aims to grow its revenue by approximately EUR 20 million through selected corporate or technology acquisitions. T-DRILL aims to grow profitably and maintain an operating profit margin of 20–25 percent in the medium term. The target is based on executing the measures set out in the growth strategy.

The Company aims to distribute 30–50 percent of the net profit for the financial year as dividends annually. The Company evaluates the conditions for profit distribution annually, ensuring that any potential profit distribution does not jeopardize the execution of the growth strategy or the achievement of financial targets.

Management interview:

Press conference today at 10:00 AM.

35 Likes

After half an hour of digging into it and running some quick numbers, this does look interesting indeed. A company combining growth with a dividend that provides an “inflation hedge.” I also liked the share of recurring maintenance operations in the business, although it could be higher. Still couldn’t quite get a clear picture of the competitive landscape in the industry and the real moats. Need to dig deeper.

As an overall first impression, this is among the most interesting new IPOs after Framery (Sensofusion is in its own deep tech category). But this could also be a pitfall—meaning the offering might end up being so heavily oversubscribed that you only get a handful of shares.

20 Likes

It remained a bit unclear when browsing the company’s website. Are these T-Drill joints as durable as welded joints? I worked in the piping industry for some time in different locations across Finland, but for some reason, I haven’t come across these on-site? Why are welded joints even used if these save time and money as promised on the company’s website? A promising company nonetheless, I’ll quite likely participate in the offering.

8 Likes

Where was the job site? Do you mean pipe joints for detached houses or apartment buildings, pipe joints for gas lines or other infrastructure, or industrial process piping joints? There are some differences between them. For years now, pipe joints in building services engineering (HVAC/plumbing) have been made using various types of fittings for many different reasons, such as hot work permits, speed, adaptability, and even cost.

3 Likes

Piping across various process industries (power plants, paper, cardboard, and pulp mills, chemical plants). “Old” weldable parts are preferred—what I’d be interested in knowing is why, if this technology is so much more cost-effective? Are there differences in durability?

1 Like

The first company in a long time whose offering I’m somewhat interested in participating in based on the numbers, but “is it too good to be true”? :thinking:

1 Like

Probably because “anyone” knows how to do welded and flanged joints. That is, you’re not reliant on a single player and their patents, even if it were a bit cheaper and easier.

1 Like

You’re right that anyone can weld flanges and make a flanged joint if they have the certifications, but if a company offers a 70% savings compared to a standard T-branch, I’d certainly use it. There must be some catch interesting technology here, and there’s definitely demand for it, but the biggest questions are how significantly this can scale and how the joint concretely differs from a welded joint?

2 Likes

The discussion about construction sites caught my ear, so here’s my take on the conversation, where I think two very different things are being mixed up.
The T-InWeld internal pipe welding process will hardly replace (manual) welding done on installation sites, nor is it intended to. This is an automated welding machine for “workshop conditions,” which is certainly well-suited for prefabrication, series production, etc., but on industrial sites, this piece of furniture weighing hundreds of kilos will hardly have any use.
The company’s page on the process in question explains pretty comprehensively what it’s all about:

The applications where welding from the inside of the pipe brings significant added value compared to traditional welding methods are, in my opinion, quite limited.
Same thing with flanging machines. Those aren’t hauled to installation sites either; they serve workshop-based fabrication.

Piping prefabrication has its own limitations as well, especially in existing industrial facilities where final dimensions and fitting have to be done on-site, so fitting and welding the piping/flanges is still left to be done manually.

But I suppose in some CAD world, they can all be prefabricated completely, leaving nothing but bolt tightening for the site…

7 Likes

It depends on the size of the project and the number of seams. If there are hundreds of flag seams on site, why wouldn’t you drag something like that to the location, e.g., on a pallet? In many industrial facilities, there’s also a workshop where contractors can work for the duration of the project. Mind you, I don’t know how that’s commissioned or what all it requires from the workstation. But just spitballing here. You might very well still be right​:+1:

2 Likes

This company is definitely worth looking into. Lifecycle services are an interesting piece here and likely provide some sort of “solid ground under your feet” in a scenario where the data center boom cools down. Of course, it will slow down at some point anyway, but the company doesn’t seem to be solely reliant on it right now, even though it has played an important role in recent growth.

I also naturally trust the cost discipline of a company from Laihia :slightly_smiling_face:

10 Likes

@Karo_Hamalainen grilled T-Drill’s Jouni Matikainen :slight_smile:

Commercial collaboration: T-DRILL Oyj

On November 18, 2026, T-DRILL announced that it is planning an initial public offering (share sale and share issue) and a listing on the Nasdaq First North Growth Market Finland marketplace during 2026.

The press release regarding the subject has been published at:
Sijoittajat - T-Drill Oy

The video was filmed in Helsinki on October 26, 2026.

6 Likes

I’ve been looking to add something seemingly boring with steady dividend payouts to my portfolio, and even just from a diversification perspective, this company started looking more appealing to me than SpaceX or other similar ones. I just need to take a closer look at the numbers and the offering price of the shares before making a final decision – they’re hardly aiming for a valuation like Anthropic’s here, which increases my interest significantly, as long as the share price hasn’t been ruined by greed :sweat_smile:

2 Likes

The valuation will probably end up around 175 + 10 = 185 million. They’ll hardly let it go for any less. If you consider it a tech company, that might be a justified price. As an engineering workshop/industrial machinery company, it would obviously be expensive.

4 Likes